The Paris PH100 is a versatile phono stage that can accommodate usage of any moving magnet or moving coil phono cartridges.  Indeed the PH 100 offers variable moving coil cartridge input impedance settings and variable gain using different jumper configurations. The resistive charge and gain setting values can be found in the technical specification page of the PH100.

 Available in black or grey with a low gloss satin finish the PH100 carries the distinctive design of the Paris series as it uses the same wooden frame as its counterpart PH200. The Paris PH100 also uses the same analog modules and RIAA circuitry as the PH200 but distinguishes itself from it by using an internal power supply unit. Enormous care went into this power supply circuit as it is in big part responsible for the PH100’s performance and musicality. The new Paris PH100 will bring you to a re-discovery of your record collection and will deliver countless hours of enjoyable and satisfying musical experience!

Fono MC      $450


Fono Mini A2D​      $175


The Aria is an "all analogue amplifier" with no digital control circuitry. The fully aluminium case screens the internal circuit from any stray RFI signals. Our designers have avoided including any superfluous gadgets as they obstruct the signal path and degrade the sound quality. The Aria incorporates many innovative design ideas including a self-adjusting servo control to keep the MC input circuit at its optimum, compensating for any variations in ambient or operating temperature.

Both stages have their own separate input sockets and input pre-amplifier circuitry. This enabled us to design bespoke input circuitry for each cartridge type without compromise. Signal switching is performed at high level and low impedance (via relays) ensuring there is no degradation of the signal.

The MC input uses parallel connected, low noise FET's (Field Effect Transistor's) configured as a compound pair. The use of FET transistors ensures there is no bias current flowing in the cartridge coil so as not to upset the delicate magnetic geometry of the cartridge. The MC input has the provision for selecting resistive input loading of 70ohms to 400ohms and capacitive loading of 1000pF to 4200pF. The input sensitivity can be changed by 6dB via the back panel.

The MM input uses low noise, bipolar input transistors also configured as a compound pair. There are two separate power supplies for each channel and further sub-power supplies for each of the low noise input circuits. Nichicon FG electrolytic capacitors have been used in critical positions throughout the power supplies. Polypropylene capacitors have been used in the signal path and equalization networks. Discrete circuitry is used throughout the signal path ensuring full control of the circuit design. 

​The Rega Fono Mini A2D is a high quality phono pre-amplifier for use with any moving magnet cartridge. The addition of USB interface allows you to easily transfer vinyl to your PC. The Fono Mini A2D is designed to amplify the signal from a moving magnet cartridge to a suitable level for all line level inputs of an audio amplifier. The new Fono Mini A2D benefits from an extruded aluminium case and very user friendly front and back panels that make this phono pre-amplifier a very easy product to use.

- Moving magnet (mm) or Moving coil (mc) operation
- High performance solid state circuit topology
- Three stages of amplification for ultra low noise
- Precise RIAA equalization +/- 0.1 dB 20-20KHz
- Massive fully regulated multistage power supply
- Toroidal transformer
- 20, 50, 100, 300, 1K, 47k 75K 100K Ohm loading options
- 0, 47, 150, 470,1K Picofared loading options
- Custom loading options available
- Hatch cover for easy loading access
- Four gain settings: 40dB, 55dB, 60dB, 65dB
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Heavy machined aluminum faceplate
- Two heavy (2 ounce) copper circuit boards
- Teflon/silver plated hook-up wire
- Detachable IEC power cord
- 17" W x 9" D x 3.5" H
- Shipping weight 18 lB
- Entirely designed and built in the USA 
- 3 year limited warranty

Aria​    $1,495


- Compatible with almost all low,medium and high output moving coil (mc)

  and Moving magnet (mm) cartridges.
- Pure tube circuit topology
- Precise RIAA equalization
- Custom Cinemag step-up transformers
- Massive fully regulated outboard power supply

- Toroidal transformer
- Internal settings with most popular loading options
- Internal setting for 150 Picofared or 0 capacitance loading
- Three gain settings: 40dB, 55dB, 64dB
- Timer delayed start for minimum turn-on noise
- Subsonic filtering 
- Ultra heavy-duty gold RCA inputs
- Precision components throughout
- Machined aluminum faceplate
- Heavy (2 ounce) copper circuit boards
- Teflon/silver plated hook-up wire
- Detachable IEC power cord
- 17" W x 9" D x 5.5" H
- Shipping weight 21lb
- Entirely designed and built in the USA
- 3 year limited warranty (six months on tubes)


Paris PH 100​      $800

Paris PH 200​      $1,660


Triton   $995


Triton   $995


The Fono MC is an exceptionally high quality MC phono stage designed to maximise the potential of any MC cartridge. Although specifically to compliment the latest Rega range of  moving coils you will find full adjustability for loading is available via dip switches conveniently placed on the rear panel with two different gain settings located on the back panel making the Fono MC compatible with most low output MC cartridges.

  • gain mm/mc 40dB / 60 dB
  • input sensitivity mm/mc 5mV/1kHz / 0.45mV/1kHz
  • input impedance mm/mc 47Kohms/120pF / 100 ohms/120pF
  • output voltage typically mm/mc 300mV@1kHz â�� 3mV / 0.3mV
  • total harmonic distortion mm/mc <0.01 / <0.05%
  • riaa curve accuracy 20Hz-20kHz / 0.5dB
  • snr mm/mc -86dB / -68dB (-94dB / -75 dB A weighted)
  • input voltage 15V/300mA AC
  • external power supply
  • rigid extruded aluminum chassis

PA 1.2​    $175

  • ​RIAA equalization +/- 1.5 dB, 20Hz to 20kHz
  • i/o connectors: rca, 3.5mm trs stereo
  • input sensitivity: 35 dB gain @1kHz, 47k Ohms Input Z
  • input capacitance: 5pf + cable capacitance
  • input impedance: 50k Ohms
  • output impedance: 1 K Ohms
  • max output level: >10dB @ 1kHz at .1% dist.
  • s/n ratio: >80 dB unweighted
  • thd .02% @ 1KHz
  • pwr: 9 – 15 VDC
  • indicator: 1 power LED

Mini​    $90

  • Sensitivity for output level 775 mV/0 dBu (with activated high gain switch)
  • Gain 1 kHz
  • Maximum input level 1 kHz
  • Signal to noise ratio (RMS unweighted) MM: 3.8 mV/1 kHz; MC: 0.38 mV/1 kHz
  • MM: 46 dB; MC: 66 dB
  • MM: 50 mV; MC: 5 mV
  • MM: 78 dB; MC: 69 dB​
  • Gain 36 dB, 46 dB, 56 dB, 66 dB
  • Channel separation > 80 dB at 10 kHz
  • Input impedance 47 kohms, 1 kohm, 100 ohms
  • 1 x custom load
  • Output impedance 5 ohms
  • Input capacitance 47 pF to 1,370 pF
  • Channel mismatch typ. max. 0.1 dB
  • Bass filter 50 Hz, 6 dB/oct.
  • Power consumption app. 15 VA
  • Outer dimensions W x D x H Audio section: 300 mm x 195 mm x 48 mm
  • Power supply: 112 mm x 312 mm x 80 mm
  • Weight Audio section: 2.25 kg
  • Power supply: 2.8 kg

Silver Cube​    $4,500

  • ​Input Stage: Dual mono Microphone preamp Chip newest generation
  • Gain settings: 36 dB, 46 dB, 56 dB, 66 dB
  • Max. gain : 66 dB
  • Internal impedances (selectable): 47 k, 1 k, 100 R
  • Onboard slot for custom impedance
  • Internal input capacitance and cap type: 47 p, 100 p, 220p, 1 n, KP 1 % and combinations (47 p always active)
  • Soft Bass Rolloff filter (toggle switch on face plate)
  • High Gain (toggle switch on face plate)
  • RIAA filter caps: MKP
  • Bass coupling after RIAA: MKP
  • Second gain stage: Dual Mono Burr Brown OPA 134
  • Discrete Output buffer for Zero global feedback (Bipolar Class A)
  • Power supply features on audio board: LC Pi-Filter, RC-Filters with extensive electrolytic bypass​

Decade​    $2,099

  • ​Input Stage: Dual mono Microphone preamp Chip newest generation
  • Gain settings: 36 dB, 46 dB, 56 dB, 66 dB
  • Max. gain: 66 dB
  • Internal impedances (selectable): 47 k, 1 k, 100 R
  • Onboard slot for custom impedance, additional hard wire slot
  • Internal input capacitance and cap type : 100 p, KP 1 %
  • RIAA filter caps: MKP
  • Bass coupling after RIAA: MKP
  • Second gain stage: Dual Mono Burr Brown OPA 134
  • Output capacitor: MKP
  • 16 different settings for optimized configuration of high pass filter
  • DIP-switch configurable
  • Discrete Output buffer for Zero global feedback
  • DC-Output jumper
  • RC-Filters with high electrolytic bypass
  • Soft Bass Rolloff filter

Black Cube SE II​     $1,149

  • ​30VA (=10x Black Cube) high-current toroidal transformer with protection coil
  • Only top notch electronic parts
  • Ultra fast recovery-rectifying diodes
  • Advanced series voltage regulation stage
  • Output voltage: app. +/- 15VDC
  • Double sided PCB
  • Detachable cable with professional 4-pole XLR connector with gold-plated contacts
  • Aluminum case
  • Dimensions: 230mmDx90mmWx44mmH
  • All connectors at the rear side Lehmann Audio Phono Preamp Features and Specifications:
  • Input Stage: Dual mono Microphone preamp Chip newest generation
  • Gain settings: 36 dB, 46 dB, 56 dB, 66 dB
  • Max. gain: 66 dB
  • Internal impedances (selectable): 47 k, 1 k, 100 R
  • Internal input capacitance and cap type: 100p, KP 1 %
  • Soft Bass Rolloff filter (selectable)
  • RIAA filter caps: MKP
  • Bass coupling after RIAA: MKP
  • Second gain stage: Dual Mono Burr Brown OPA 134
  • Discrete Output buffer for Zero global feedback
  • Output capacitor: MKP
  • DC-Output jumper
  • Power supply features on audio board
  • RC-Filters with high electrolytic bypass

Black Cube SE​    $929

  • ​Input Stage Dual mono Microphone preamp Chip newest generation
  • Gain settings 36 dB, 46 dB, 56 dB, 66 dB
  • Max. gain 66 dB
  • Internal impedances (selectable) 47 k, 1 k, 100 R
  • Onboard slot for custom impedance plus additional hard wire slot
  • Internal input capacitance and cap type: 100 p, KP 1 %
  • Soft Bass Rolloff filter (jumper)
  • RIAA filter caps : MKP
  • Bass coupling after RIAA: MKP
  • Second gain stage: Dual Mono Burr Brown OPA 134
  • Discrete Output buffer for zero global feedback -
  • Output capacitor: MKP
  • DC-Output jumper
  • RC-Filters with high electrolytic bypass​

Black Cube Original​    $629

  • Selectable gain: 31dB, 41dB, 51dB, 61dB
  • Input impedance: selectable 47k, 1000 or 100 ohms
  • Free slot for custom impedance load
  • Input capacitance: 100pF
  • Passive RIAA-filter with high performance MKP foil capacitors
  • Soft bass roll-off filter (6dB/Okt @ 60Hz), jumper selectable
  • DC output jumpers
  • Double-sided audio board layout for optimal parts placement and trace routing
  • Burr Brown audio grade operational amplifiers
  • Gold-plated RCA audio connectors
  • External AC power supply
  • Nonmagnetic aluminum case

Black Cube Statement​    $449

  • ​Phono to line level preamplifier
  • Total phono solution
  • Matches any cartridge type
  • Fully user adjustable
  • Very low noise
  • Very high RIAA accuracy
  • No hum!
  • Includes patented 'Phono Enhancer' option
  • Low cost, very high performance
  • new mk3 offers significant performance upgrade

P-75 Mk3​     $895

​The OBH-15 mk2 has a completely new circuit design, with a discrete transistor MC and integrated circuit MM stage. Unlike its predecessor, the new amp has multiple gain settings and matching capabilities for capacitance and resistance. The signal required by most modern amplifiers is described as being ‘LINE’ level which is, in technical terms, between 200 and 500 milli-Volts sensitivity with a flat frequency response. Unless your amplifier has a specific ‘Phono’ or Disc input, the level will be too low to play vinyl and the frequency response will be wrong.

OBH-15mk2​    $595

  • Freqency response 20 Hz to 20KHz + or - 0.05 db

  • Gain MM 34 dB MC 26dB MM + MC 60dB

  • Hum and noise MM greater than 80 dB, MC greater than 66

  • Distortion 0.05 % IM and THD

  • Overload MM 0.52 volts, MC 0.025 volts @ 1000 Hz

  • Input Impedance MM 47,000 ohms, MC 1000 ohms

  • Size 192mm W x 78mm x H 52mm D280

  • Weight 2.3Kg's

  • Signature model weight 3Kg's

Soloist Phono Amp           $995

Special Edition Version   $1,200

​The vp530 is a usb/tube phono preamp for use with moving-magnet and high output moving-coil cartridges. It includes a built in headphone amplifier, Burr-Brown A2D converter w/usb output, and RIAA curve/flat EQ. The vp530 is designed to amplify an RIAA equalized phono signal to a hi-level signal or provide a usb digital output. Since the unit utilizes tube circuitry, the resulting output signal is more warm and musical than solid state preamplifiers. The real kicker aside from the price and stellar sound is that it's manufactured in the US.

VP 530​    $399

​The VP130 is a well designed RIAA phono preamplifier made to equalized phono signal to a line-level signal, and is intended for magnetic pickups. Since the unit utilizes tube circuitry, the resulting output signal is more warm and musical than solid state preamplifiers. It's the perfect blend of price and performance. Get the magical warmth of a tube phono preamp for an unrivaled price. This compact and affordable preamp effectively boosts the phono signal for any cartridge with an output of 3-5mV. It has a compact circuit board and uses a single 12AX7 tube in the output stage for that luscious midrange only tubes can provide. It’s also dead quiet, with a signal-to-noise ratio of 80dB. The VP130 also has a few added features that everyone will appreciate, including a 1/4” headphone jack on the back panel, a mute switch, a 20Hz (infrasonic) rumble filter, and separate output volume controls for the mains and headphones.

VP 130​    $275

Telephone: (954) 921-1408

E-Mail: hwdsound@aol.com